1. Home
  2. RV Roof Vents
  3. Heng's
  4. Heng's Vortex
  5. Installed Heng's 90046-CR Vortex II Multi Speed 12 volt Fan - Complete Roof Vent
Installed Heng's 90046-CR Vortex II Multi Speed 12 volt Fan - Complete Roof Vent
Installed Vortex II

Installed Heng's 90046-CR Vortex II Multi Speed 12 volt Fan - Complete Roof Vent

0 Review(s) Write a Review
Your Price: $95.99
Part Number: VX2-INT-
Availability: This item is currently out of stock and no date for arrival has been given. 0 Free Shipping.

Choose Options

*
*

BEFORE YOU PURCHASE

Free Shipping (when offered) is for the 48 ContiguousU.S. ONLY


Economy / Free / Fedex Smartpost / Parcel Select are delivered by USPS MAIL (Post Office)

Transit times 7 - 14 business days


Larger Items that don't fit in mailbox carrier may decide not to leave you will need to arrange delivery with the carrier.

Check Address is correct & complete, Lot #, Apartment #, Suite #

RV Roof Vent with a Vortex II Installed in Unit


Vent Lid Choose Color


**12 volt ONLY 110/115/220 volt such as in a house or generator will damage the unit**

12 volt Fan Motor

9' Fan Blade

1.8 amps of power required


Multiple Speed Fan

Vortex Fan Speed 188 CFM (188 Cubic Feet Per Minute)

High Velocity air fan system - over 300% more air flow movement

Multiple Speed Fan 3 Speeds Outward and 2 Speeds Inward


Removable Fine Mesh Screen included

Manual Crank Style Handle Included


Available Inside Garnish ShroudSizes 1" / 3" / 4" / 5" / 6" Vertical Leg (How far up into your ceiling it goes)

1 ¼” Wide Mounting Flange (trim you see inside on the roof)

Color White


No Mounting Hardware you must provide screws and caulk / butyl tape


If upgrading non-powered vent 18 Gauge Wire to 12 volt DC recommended

Testing Unit before installing you must have unit facing correct direction, face down like when installed in rv, or blade will rub


DO NOT let the unit hang by wires as you will damage the unit


If upgrading non-powered vent 18 Gauge Wire to 12 volt DC recommended

Testing Unit before installing you must have unit facing correct direction, face down like when installed in rv, or blade will rub

Remove garnish ring from existing roof vent and save screws for re-installation

Remove crank handle, screen and fan unit from existing roof vent


Existing Ventline Vents: Unscrew and move gear drive to alternate position as shown on installation instructions

Existing Jensen Vents: Unscrew and move gear drive to alternate position as shown on installation instructions

Hold Vortex unit near ceiling and attach Vortex wires to RV 12 volt power wires

Do Not let the unit hang by wires as you will damage the unit


Secure Vortex unit onto existing vent frame, making certain the crank spindle is properly aligned and seated in the matching gear drive (if necessary use knob to rotate gears to achieve alignment)


Secure gear drive spindle with screw

Make sure wires are out of the way of the fan blade

Attach screen frame, inserting 4 tabs and rotating clockwise until tight

Attach manual crank knob with screw

Reinstall original garnish ring


Related Items

6
$4.95
(0)
In Stock. Free Shipping.
Flexible LED Navigator Map Reading Light Black
$21.99
(0)
In Stock. Free Shipping.
6
$30.25
(0)
This item is currently out of stock and no date for arrival has been given. Free Shipping.
Momentary Rocker Switch for Heng's Range Hood Monitor Panel
$8.25
(0)
This item is currently out of stock and no date for arrival has been given. Free Shipping.
WASTE TANK 48 Gallon Black Water Holding Tank
$215.99
(0)
In Stock. Free Shipping.

Browse Similar Items