PLEASE NOTE: You CAN NOT use a City fill dish to fill Class A Customs Fresh/Gray Water Tanks for fresh water use - the city fill is a pressurized connect and all Class A Customs Fresh / Gray / Waste Tanks are gravity fed and non-pressurized. The city fill by passes the water tank and runs directly to your water heater and sink.
You can use a Gravity fill dish with all of Class A Customs Fresh/Gray Water Tanks for fresh water use - this is how you fill the water tank, you do not use a fill dish with Class A Customs Gray or Waste Water Tanks.
Direct OEM replacement
UV and impact resistant
Durable Plastic
Resistant to road salts and acids
Paintable
Tapered Inlet Connection allows for use with Class A Customs 1.25" Food Grade Water Hose OR Class A Customs 1.375" Food Grade Water Hose - In Plumbing Category
Air Vent connection allows for use with the Class A Customs .5" Food Grade Hose - In Plumbing Category
City Fill includes a Plastic Check Valve with 1/2” MPT Connection and Inline Screen
Measurements SEE PHOTOS
Cutout Dimensions: 3-3/4” H x 6” W
Outside Flange Dimensions: 5-5/16” H x 7-9/16" W
Valve Depth Overall: 2-1/2”
CAUTION: Improper installation, operation, or servicing will result in equipment damage and personal injury. This product should be installed and serviced by qualified technical personnel who are familiar with the construction, "operation", & potential hazards of this type of connection.
Over-tightening mounting screws may cause product to distort.
Over-tightening any plumbing connections will result in leaking and product damage. Plumbing connections installed in a "binding" condition create excessive stress on product which may result in leakage or damage.
Failure to follow these instructions for installation of our product will forfeit any warranty consideration.
1. Install gravity fill spout into dish by feeding tapered end of spout through hole in center of dish. Make sure locking tabs on tapered side of spout are on back side of dish
2. With front side of dish facing you, turn tapered spout counter-clockwise until it makes a clicking sound. This will lock the gravity spout in proper position.
3. Cut a 3-1/2" diameter hole in sidewall & feed plumbing connection through opening.
4. Apply appropriate putty tape or foam gasket to back of dish / flange. Make sure mounting holes are covered WHEN USING GASKETS BEHIND THIS PRODUCT, KEEP UNIFORM THICKNESS AROUND PERIMETER!!
5. Using 100% silicone caulk, apply behind check valve to ensure waterproofing.
6. Connect plumbing line from fresh water tank to back of gravity spout inlet & secure with a clamp Gravity inlet fitting will accommodate 1-1/4" or 1-3/8" hose.
7. Position dish into cutout opening on sidewall & secure with (3) #8 self-tapping screws. DO NOT OVERTIGHTEN SCREWS DURING INSTALLATION!! OVERTIGHTENING WILL CAUSE PART DISTORTION
8. Cap seal outside perimeter with caulk for waterproofing.
CAUTION: Improper installation, operation, or servicing will result in equipment damage and
personal injury. This product should be installed and serviced by qualified
technical personnel who are familiar with the construction, "operation", & potential
hazards of this type of connection.
Over-tightening mounting screws may cause product to distort.
Over-tightening any plumbing connections will result in leaking and product damage.
All plumbing connections made during installation should be hand tight plus 1/4 turn.
Plumbing connections installed in a "binding" condition create excessive stress on product
which may result in leakage or damage.
Never push check valve on city water inlet down to relieve pressure. O-ring failure will result.
Failure to follow these instructions for installation of our product will forfeit any warranty
consideration.
1. Cut a 3 1/2" diameter hole in sidewall & feed plumbing connection through opening.
2. Apply appropriate putty tape or foam gasket to back of dish / flange. Make sure mounting holes are covered WHEN USING GASKETS BEHIND THIS PRODUCT, KEEP UNIFORM THICKNESS AROUND PERIMETER!!
3. Using 100% silicone caulk, apply behind check valve to ensure waterproofing.
4. Connect plumbing line for the city water connection to back of threaded city water inlet.
PLUMBING CONNECTIONS SHOULD BE HAND TIGHT PLUS 1/4 TURN - DO NOT OVER-TIGHTEN FITTING.
5. Position dish into cutout opening on sidewall & secure with (3) #8 self-tapping screws. DO NOT OVERTIGHTEN SCREWS DURING INSTALLATION!! OVERTIGHTENING WILL CAUSE PART DISTORTION
6. Cap seal outside perimeter with caulk for waterproofing.
Related Items
$16.99
In Stock.
Free Shipping - View Shipping Method Tab Below
_thumbnail.jpg)
$15.99
In Stock.
Free Shipping - View Shipping Method Tab Below
_thumbnail.jpg)
$27.99
In Stock.
Free Shipping - View Shipping Method Tab Below
_thumbnail.jpg)
$21.99
In Stock.
Free Shipping - View Shipping Method Tab Below
$21.99
Out of Stock.
Free Shipping - View Shipping Method Tab Below
$23.99
In Stock.
Free Shipping - View Shipping Method Tab Below
$27.99
In Stock.
Free Shipping - View Shipping Method Tab Below
$15.99
In Stock.
Free Shipping - View Shipping Method Tab Below
_thumbnail.jpg)
$16.99
In Stock.
Free Shipping - View Shipping Method Tab Below
$16.99
In Stock.
Free Shipping - View Shipping Method Tab Below
