1. Home
  2. RV Roofing
  3. TPO RV Roofing
  4. Class A Customs TPO 9.5 Foot Wide RV Roof Kit
Class A Customs TPO 9.5 Foot Wide RV Roof Kit
Class A Customs TPO 9.5 Foot Wide RV Roof Kit

Class A Customs TPO 9.5 Foot Wide RV Roof Kit

0 Review(s) Write a Review
Your Price: $169.00
Class A Customs TPO 9.5 Foot Wide RV Roofing Kit
Part Number: TPO-KIT-95
Availability: In Stock. 23 Free Shipping.

Choose Options

*

Membrane Ships Folded  Depending on size of kit you will get one or two boxes (glue / membrane)

Membrane Length / Width It is recommended to get a length that is longer / wider than your unit due to possible curve of the roof, raised or lowered areas, removing the excess is much better than not having enough.



Kits 5 Foot Long Membrane and Adhesives

Membrane 9.5 foot wide x length selected
2 Tubes of Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube)
2 Rolls of Putty Tape (1/8" Thick x 3/4" W x 30' L)
1 Gallon of Class A Customs Acrylic Water Based Adhesive

 

Kits from 10 Foot Long - 25 Foot Long Membrane and Adhesives

Membrane 9.5 foot wide x length selected
4 Tubes of Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube)
2 Rolls of Putty Tape (1/8" Thick x 3/4" W x 30' L)
1 Gallon of Class A Customs Acrylic Water Based Adhesive


Kits from 30 Foot Long - 45 Foot Long Membrane and Adhesives
Membrane 9.5 foot wide x length selected
5 Tubes of Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube)
4 Rolls of Putty Tape (1/8" Thick x 3/4" W x 30' L)
2 Gallon of Class A Customs Acrylic Water Based Adhesive


Installation Help

TPO Membrane
Single-ply membrane, lighter weight than EPDM
COLOR White - Color is same throughout substrate, can be applied either side
Will not chalk, fade, or leave streaks down the side of your RV
Brilliant UV performance and is resistant to mold, algae, and fungus
THICKNESS 32mils
Better puncture resistance than EPDM at .028 Thick
Will not shrink or crack (100% solids sealant)
Stretches easier so you can get a perfect, tight fit
Can be easily repaired.

 
Class A Customs Acrylic Water Based Adhesive
Water base adhesive designed for use as a bonding adhesive for single ply roofing membranes.
Designed to Bond EPDM, PVC, and Hypalon to wood fiberboard, plywood, EPS, any typical polyisocyanurate insulation, gypsum, concrete, etc.
May be applied by spray, roll coating, or by brush.
Grows stronger and adheres more with age.
Remains flexible to compensate for expansion and contraction of the membrane itself.
COLOR White
COVERAGE 160-200 sq ft/gal (1side @ 8-10 mil)
May be applied by spray, roll coating, or by brush.
(When using spray application an Aro 650095 4.25 inch air motor with a 30:1 ratio pump @ 80 psi using a 651-500 gun equipped with #651551 quick clean and spray tip #T.C. 1565 with 0.015 orifice or similar equipment is recommended).

For maximum bond strength a two-sided application is recommended.
If one surface is porous, such as plywood or fiberboard, it is acceptable to wet laminate the membrane to the substrate.
If both surfaces are non-porous, such as EPS or ISO apply the adhesive to both surfaces 4 - 5 mils and allow to dry approximately 20 - 30 minutes, depending on conditions.

Adhesive will turn from white to clear when it is dry.
Apply membrane to roof deck and roll or broom down sheet to assure 100% contact area.
DO NOT FREEZE - KEEP OUT OF REACH OF CHILDREN


Putty Tape
Non-hardening, pliable putty tape.
Color Gray
Waterproofs overlapping metal seams.
1/8" high X 3/4" wide - Roll 30 feet long

 

Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube)
All weather self-leveling sealant designed and formulated to provide excellent weather resistance.
It features high solids, low V.O.C. content, and no hazardous air pollutants (HAP).
This compound provides good adhesion to a variety of substrates.
This product has good low temperature resistance and will not crack at -40oF.
Typically used in RV applications where a long-term weather tight seal with good ozone and UV resistance are required.
Cured sealant is paintable.
Surfaces should be free of dirt, oil, or other contaminants. A solvent cleaned surface is optimum.

PRECAUTION ON ALL PRODUCTS
This material in the liquid or vapor phases is extremely flammable. Keep away from sparks and open flame - do not smoke by this product.
Avoid prolonged breathing of vapors of this product - use in a well ventilated area. Prolonged breathing of vapors may cause headaches and even unconsciousness.

Direct contact of uncured sealant irritates eyes and may irritate skin. In case of eye contact flush eyes with water for 15 minutes and call a physician. In case of skin contact, thoroughly wash skin with soap and water.

Material may be harmful or fatal if swallowed. If swallowed, do not induce vomiting. Seek medical attention immediately.

 

Warning: Cancer and reproductive harm. www.P65Warnings.ca.gov.


Installation Help 

  1. Route all necessary vent and accessory openings. Sand all wood decking openings, seams and edges to a smooth surface. Blow debris off roof (wood decking) with air hose.
  2. Apply duct tape (2” minimum width) evenly onto roof and sidewall to cover sharp metal or fiberglass edge.
  3. Optional: Apply a porous tape (masking or fiberglass mesh) to seam the decking where butted together. This will help hide decking seams and give the finished roof a smoother appearance while strengthening the joint.
  4. Make sure all screw heads and surface is smooth and level throughout.
  5. Remove membrane from box as soon as possible onto clean roof of unit. Do Not allow membrane to touch ground or dirty surface. Do Not allow membrane to touch sharp objects or surfaces. Membrane can be glued either side down.
  6. Cut the roof sheet to fit roof length with an excess of at least 6” front and rear. Square as required.
  7. “Bed Sheet” the roof. That is, fold it in half so half of the deck is exposed.
  8. Apply adhesive in a wet film thickness of 8-10 mils with a paint roller or brush to the exposed half of the roof deck. (1 gal. will cover approximately 160-200 sq ft.)
  9. Lay the roof membrane over the wet adhesive.
  10. Before removing air pockets with a squeegee (gray neoprene head will not streak), the membrane must be lifted and pulled taut from each of the four corners of the roof. The membrane needs to be adjusted both in width (side to side) and length (front to rear) to ensure the roof is as flat as possible before the squeegee process.
  11. Remove all air pockets with a squeegee; press firmly working from the center outward toward the edges. All wrinkles must be removed at this point for a quality installation. The roof will tighten and conform as the adhesive cures.
  12. Repeat steps 6 through 11 for remaining half of roof. (In mass production situations the entire roof may be glued all at once.)
  13. Using a utility knife “x” cut all roof openings. Make sure you round all 90-degree corners to eliminate the possibility of running cuts. Surplus material can be stapled inside the vent openings. Let surplus material drape over the side of the unit for perimeter finishing. The roof edges can be sharp – it is required that duct tape be used to avoid edge splits.
  14. Apply putty /butyl tape to the backside of the roof-edge molding. Then while holding the bar, draw surplus material tight with a downward pull. Attach the drip edge bar, working outward from the center of the unit. When fully installed, use a utility knife to cut surplus material from below the bar.
  15. Assemble and attach roof molding where the roof membrane meets the front and rear end caps. Remember the roof molding must be secured to a cross member.
  16. Apply putty/butyl tape to all vents and accessories on the roof.
  17. Seal around all vents and accessories. Apply sealant to all visible screw heads. Both edges of the front and rear roof molding must also be sealed. There is no need to spread the sealant as you are applying it. A minimum 3/8” bead will work for most applications.
*Butyl tape provides the “Primary Seal” against water infiltration or penetration in these membrane roof assemblies. The lap sealant is a secondary seal.

* Butyl tape must be compressed 30% to 40% to perform correctly.

Related Items

Heng's 9
$29.95
(0)
Not for Sale. Free Shipping.
1
$6.79
(0)
In Stock. Free Shipping.
1.25
$6.99
(0)
In Stock. Free Shipping.

Browse Similar Items