View ALL Photos & READ Product Tabs Below

13 Gallon Fresh / Gray Water Holding Tank

Your Price: $53.49

Questions about this item? Ask here.

Part Number: T-1300

Availability: In Stock. 136

Free Shipping - View Shipping Method Tab Below

Quantity	Price
5 - 9	$52.04
10 - 24	$50.49
25+	$48.49

Quantity

Description
Questions & Answers
Product Features
Preparation & Installation
Food Vendors
Warranty
Shipping Method

Non-Pressurized Tank all tanks we carry must be vented, Basic Plumbing Example

Tank Measurements +/- .25" on each measurement due to manufacturing process

21” does not include fittings x 9” x 16” (rotate tank to change height or width)

Average tank thickness .219 or 7/32" thick (just under 1/4")

Installed Fittings See Photos
Two) 1.5" Female NPT Fitting - fitting is sealed to use remove membrane with razor knife
Two) .5" Female NPT Fitting - fitting is open

Q: Can the tanks be rotated 90 degrees ? Looks like fitting wind still work

Asked by: Max - 6/21/2024

A: The tank can be placed on any side but must be braced and secured.

You can find more information on this and more at our Water Tank Helps Page located at the top of each page. https://www.classacustoms.com/Water-Tank-Helps_ep_41.html

Answer provided by: Customer Service (7/5/2024)

Q: We're trying to get RVIA certification using your tanks, however, they will not accept tanks without NSF certs molded on the tank itself. Do you help with RVIA certification at all or know of any customers who have RVIA using your tanks?

Asked by: Denny - 5/31/2023

A: We are not RVIA associated, we are not aware of thier rules and regulations. Thank you.

Answer provided by: Customer Service (9/26/2023)

Q: I have a space problem. Can I stack two of the t-1300 tanks one on top of the other and pipe them together to get 26 gals. The space I have is 21” wide x17.5” deep and 24” high Or do you have another tank that would fit in this space. Thanks

Asked by: Joe - 2/26/2023

A: Can I stack the water tanks on top of each other?
Can I put weight on the tanks?
No, do not place anything on the tanks, if you need to stack the tanks you will need a weight bearing shelf between them. A gallon of water weighs roughly 8.34 pounds, so a 40 gallon water tank when full is over 335 pounds in weight.

Answer provided by: Customer Service (5/31/2023)

Questions about this item? Ask here.

Made In USA Class A Customs manufactures these tanks and is located in Elkhart, Indiana

Fresh and Drinking Water Safe great for rvs, food vendors and extra water storage

BPA Free Class A Customs does not carry this chemical nor uses it in the manufacturing process

NSF Certified Materials Tank & fittings made from DOW NSF International NSF/ANSI Std 61 approved Medium Density Polyethylene (MDPE) Resin

NO NSF LOGO Class A Customs NSF Letter (on Water Tank Helps Page) explaining why we no longer have the NSF Logo in our tanks, however, Class A Customs Fresh/Gray Water Tanks are still made from the same NSF Approved Materials.

Forward this letter onto your inspecting Health Department before ordering to be sure tanks will work for your application and get approval.

UV-8 Stabilization

Complies with
U.S. FDA 21 CFR 177.1520 (c)3.1a
Canadian HPFB No Objection
Underwriters Laboratories Inc.
EU, 10/2011
NSF International NSF/ANSI Std 61 (sec 4 & 5)

Non-Pressurized Tank all tanks we carry must be vented, Basic Plumbing Example
Fresh or Gray Water Use ideal for rvs, food vendors and extra water storage
Seamless One-piece seamless construction, no seams to burst
Rotatable tank can be placed on any side
Resistant Stain, Corrosion and Rust Resistant
Color Creamy White in color so you can see waterline through tank
Made From Medium Density Polyethylene (MDPE) Resin - glues do not stick to this material and easily cleaned.

OEM Part

No retail box - no install instructions

Have a certified technician install all parts to prevent product damage and personal injury

Helpful information & answers to common questions can be found on the Water Tank Helps Page

Additional Fittings

To install additional fittings anywhere on the tank we recommend Uniseal Fittings, you can have from .5" up-to 3"

We do not take orders for custom fitting placements or sizes unless bulk ordering, 100 or more of each tank per order.

Custom Water Tanks

We can make a custom tank however due to the cost of a mold ($8,500 and up) most customers needing only a few tanks find it better to use a tank we already manufacture.
For more information and a quote on custom tanks please fill-out our Water Tank Build Form.

Preparation
Sanitize each tank prior to use to remove any debris from the manufacturing process

Tanks are made in a warehouse, wipe with a damp cloth to remove surface dust or scuffs

Installation & Plumbing
Non-Pressurized Tank all tanks we carry must be vented allowing air in and out when in use, Plumbing Examples
Do Not hook a garden hose directly to tank damage will occur, it is recommended to use a fill dish or other gravity process
Do Not over-tighten fittings as damage will occur.

It is recommended to use plastic NPT male fittings with plastic female NPT fittings to avoid damaging the threads, metal thread fittings can crush the plastic threads.
Very little, if any, pipe thread tape is needed using too much pipe tape will damage the threads. We do not recommend pipe dope as you can not remove the fitting later, if used be sure to use a food safe brand.

What fittings will I need for my plumbing?

This will depend on how you are setting-up your tank and will vary by application, we are not aware of what items you will be needing, please view the Plumbing Examples

Water Tank Monitors & Probes

Water Pumps

Mounting & Bracing
Tank can be placed on any side.
Place tank on level surface and brace to prevent tank from moving during transit.
Tank needs to be adequately supported, examples on the Water Tank Helps Page
Do Not hang by ratchet straps, this is too thin and will not adequately support tank.
Do Not place weight on tank, if you need to stack the tanks you will need a weight bearing shelf between them.

Can I install the tank under the trailer?
Tanks can be installed inside or outside of unit, for food vendors verify requirements before purchasing as some areas do not allow tanks to be outside of the unit and others do not allow the tank to be inside of the unit.
Be sure to Sanitize Tank before installing.

All tanks must be braced and secured to prevent any movement of the tank while in transit and to prevent possibility of tank tipping or falling.
Due to the manufacturing process all the tanks especially the larger in size will have a bowing to the walls, when the tank is filled the tank will expand out removing the inward bow, we recommend laying all tanks on a level surface (this can be angled to help with drainage) and bracing the tanks. For larger tanks it is recommended to brace all side walls with plywood or metal, we do not recommend using ratchet straps on the tanks alone as this is a large amount of weight on a thin strip and may cause cutting into the tank. For tanks placed outside it is also recommend to enclose tanks using sheet metal / plywood or some other type of weather proof material to prevent damage from road debris and speed bumps, be sure to check your clearance before ordering.

Brackets or Strap Systems Due to the variety of installations we do not carry brackets or bracing systems.

Before you build or modify unit, you need to verify rules and regulations.
Codes vary by local health departments, not state.

We are not aware of the codes or rules. We are not aware of what tanks or items you need.

Ask your inspector BEFORE purchasing

Size Requirements (Gallons / Measurements / Fresh to Gray ratio)

Does the bottom need to be slanted? Can I place the tank on a slanted surface as this would make the tank then slanted?

Fittings Requirements (Size / Placement / Materials)
Filling Procedure Requirements (Lockable Fill Dish / Materials)
Tank Placement Requirements (Inside / Outside of unit)

Clean Out Requirements Do I need a clean out? What size does this need to be?

Class A Customs Tanks have NO NSF LOGO - read below for why

Water Tank Percent Calculation Examples
Multiply (fresh tank size) x 1.15 (1 . 15%) = Tank needed
30 x 1.15 (15%) = 34.50
30 x 1.50 (50%) = 4

NO NSF Logo
Tanks no longer have the NSF logo molded into them due to changes NSF made regarding the use of the NSF logo. The NSF Company does not allow for end users to use the NSF logo unless each item has been inspected and a certification paid for each item, the material that all of our tanks are made from are still the same NSF Certified Material, adding this extra step of certification is an unnecessary step but generates revenues.

The NSF Company does not allow vendors/manufacturers to link to the NSF paperwork unless verified NSF products are being used, our company has been verified and therefore is allowed to link to the NSF Certified Materials on the NSF Website. If needed your inspector can check on this regarding our company and website as we have already provided this information to the NSF company and have been advised on how to correctly use/link to the certification information on our website.

What does my inspector need when I go to inspections on the tanks?
Class A Customs NSF Letter (on Water Tank Helps Page)
Receipt of Purchase
All tanks have the part number molded into the tank, inspector can verify tank.

Manufacturer Warranty
Class A Customs, LLC Manufacturer Warranty covers manufacturer defect on manufacturer installed fittings and tank workmanship.

Inspect tank and all fittings before beginning installation, there is a 14 (fourteen) day time period to report any damages once you items are received. Cross-thread and thread damage is not covered once you have installed a connecting fitting into the tank fitting.

Warranty does not cover tank or fitting damage resulting from tank or fittings plumbing being jarred, moved, cracked, cross-threaded, damaged threads from use, and/or fitting punched from tank. Such damage is due to plumbing being moved and/or tank being jarred causing unavoidable damage beyond manufacturer control or responsibility.

Warranty does not cover tank or fitting damage due to customer improperly venting tank.

Warranty does not cover damage to tank from weight being on tank or tank being compressed by outside forces, example, tank being buried underground causing collapse; tank being compressed under boat.

Warranty does not cover damage to tank or fittings due to weather related incidents, example, tank freezing or being in excess heat/sun expose.

Using Class A Customs, LLC Fresh/Gray Water Holding Tank for any purpose other than fresh or gray water storage will void any/all warranty.

Using Class A Customs, LLC Black/Gray Waste Water Holding Tank for any purpose other than black (human waste) or gray water storage will void any/all warranty.

Using any Class A Customs, LLC water tanks for fuel, chemical or other storage voids warranty.

30 Day Return Policy
Some items are nonreturnable and include but not limited to:
All Fuel Pumps
Electrical Items
All Water Pumps

Customer will need to return all merchandise in new, unused condition and packing materials if available.
To return item customer will need to pay return shipping. Packages refused or return to sender will not be delivered back and no credit/refund will be issued.
Original Shipping is non-refundable, 20% Restock fee will be charged for all orders.

Returns c/o Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
Phone: 574-206-0101

Include a copy of original purchase receipt and write order number on each box
Save the tracking numbers for your records, we are unable to search for a package online without tracking numbers.

Return Process
This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes to return the correct item. We'll notify you via e-mail of your refund once we've received and processed the returned item.